IGS-2824G-450 – 24 Ports POE Ethernet Switch




IGS-2824G-450 is a 24 ports PoE Ethernet Switch is a security surveillance Ethernet Switch which aims at Ethernet high definition surveillance and security system. The product fully combines the characteristics of security surveillance, provides fast packet forwarding ability and abundant backplane bandwidth, which ensures clear image and fluent transmission. ESD and surge protection circuit can improve product stability. The product supports VLAN, function can restrain the network storm, protect the information security, prevent the viral transmission and cyber attack, fully satisfy the Ethernet video security surveillance system and Ethernet project needs.


igs 2824g 450 2 application result


  • Major ports: 24x 10/100/1000Mbps PoE ports, 2x 10/100/1000Mbps uplink port, 2x 10/100/1000Mbps SFP port, every port supports MDI/MDIX;
  • Special function: downlink ports can only communicate with uplink ports;
  • Standard: IEEE802.3af/at, POE pin: 1/2+,3/6-(End-span), the remaining lines (4,5,7,8) can be used for other program;
  • Protection: Excellent anti thunder, anti static and anti-interference ability.
  • Operation: Plug amd Play, No Setting required.


The transmission distance is related to the connected cable. We suggest standard Cat5e/6 network cable to make sure transmission distance can up to furthest!

Board Diagram

igs 2824g 450 3 board diagram application result


1) Device must be connected with lightning protection grounding,otherwise protection level will reduce;please use above No.20 wire to connect the grounding terminal.
2) Turn the dial switch for left,the equipment can enter surveilance mocule after providing equipment power.

Installation steps

Please check the following items before installation, if it is missing, please contact the dealer:

24 ports PoE Ethernet Switch1 pcs
AC power cable1 pcs
Accessory1 pcs
User manual1 pcs


Please follow the below installation steps:

1) Please turn off the signal source and the device’s power before installing, installation with power on may damage the device;
2) Use network cable connect PoE IP camera 1 ~ 16 downlink ports of product respectively;
3) Use a network cable connect equipment uplink port and NVR or computer;
4) Connect power adapter.
5) Check if the installation is correct,equipment is in good condition, the connection is stable, then power on for system;
6) Ensure the Ethernet equipment with power on can work properly.


Item Description
PowerPower Adapter Voltage 110 – 240V AC
Consumption 450W
Network Connector Networt PortPOE Ethernet Port1~24 Port: 10/100/1000Mbps
Ethernet portUplink Port: 10/100/1000Mbps
SFP PortSFP Port: 10/100/1000Mbps


Transmission Distance AA

1~24 Port: 100Mbps: 0~100m
Uplink Port: 0 ~ 100m
SFP: depends on the optical module (Combo)


Transmission Medium

Cat5/5e/6 standard network cable


Network Standard



Switching Capacity



Packet Forwarding Rate



MAC Table

Power Over Ethernet


POE Standard

IEEE 802.3af/IEEE802.3at


POE Power Supply Type



PoE Power Consumption

af≦15.4W, at≦30W (every port)
LED Status Indicator VLAN/Ext end


POE Ethernet LED Indicator

Power: 1 red light indicates
that the power normal work
POE: 24 yellow lights indicate that the POE is power on
Ethernet: 28 green lights indicate that the Ethernet link and act;


Working temperature

0℃ ~ 55℃


Relative Humidity

20 ~ 95%


Storage temperature

-20℃ ~ 70℃


Dimension (L x W x H)

440 mm *290 mm *45mm










Specication change will not be noticed.

(*) Made in China

Download Datasheet

download bottons result

Trouble Shooting

Please follow the steps if the equipment has trouble:

  • Make sure the equipment is installed according to the manufactures installation guide.
  • Confim RJ45 cable order meets EIA/TIAS68A or 568B standard.
  • Every PoE port can provide PoE equipment maximum power less than 30W, please do not connect the PoE equipment with power over 30W.
  • Replace the equipment with a proper functioning 4 ports PoE Ethernet Switch to check if the equipment is damaged.
  • Please contact your vendor if trouble still exists.

Plug Producing Method

Instruments to be used: wire crimper, network tester. Wire sequence of RJ45 plug should conform with EIA/TIA568A or 568B;
1) Please remove 2cm long the insulating layer, and bare 4 pairs UTP cable;
2) Separate the 4 pairs UTP cable and straighten them;
3) Line up the 8 pieces of cables per EIA/TIA 568A or 568B;
4) Cut off the cables to leave 1.5cm bare wire;
5) Plug 8 cables into RJ45 plug, make sure each cable is in each pin;
6) Use the wire crimper to crimp it;
7) Repeat above 5 steps to make the another end;
8) Use network tester to test the cable if it works;

igs 2824g 450 4 plug producing method result.webp